The electrostatic contermeacure brushes' principles.
Electrostatic removing brush, data
CONTENTS
  1. Roughly
  2. Electrostatic removing performance
    - a primary factoring and principle
  3. Characteristic with a kind of an electrode
    1. Carbon fiber
    2. Stainless steel fiber
    3. Sunderion Plastic fiber
    4. Heat-resistant Dina fiber
    5. SA-7 fiber
    6. Amolfas fiber
    7. Electrostatic removing seat
  1. Roughly

    now preparing.

  2. Electrostatic removing brush,
    - a primary factor and principle

    [Primary factor]
    1. Electrostatic removing effect gets expensive, on the condition that I make a line diameter.
    2. By rubbing with an elecrified substance. An electrostatic removing performance rises.
    3. A good person, can remove a static electricity early for a guidance common property talent.

    [Principle]
    Guidance electricity of for the bundle to collect a thin line electrified coming into the posses mutually, strong unequal electrolysis occurs when coming in contact. Of the inside of an electrified body electrified, an electrical charge is neutralized, and then a static electricity is removed.
    (In the same way as an effect of a lightning rod against a thunder, of the action principle.)

  3. Characteristic with a kind of an electrode
    1. Carbon fiber
      ·Line diameter=7µm
      ·electric peculiar resistance=10-3ohms/cm
      Carbonized, type it strongly, scientific fiber carbonic fiber, for a triboelectricity, electric resistance low, aline diameter is extremely small. An electrostatic removing, effect is the best. However, a cutting stress can easily occur for a piece, of a fiber, weakly. Are thought that it is better that I avoid a use around a high-pressure circuit for this reason rather.
    2. Stainless steel fiber
      ·Line diameter=12µm
      ·electric peculiar resistance=10-5ohms/cm
      With the object to have been thin, roll it for a stainless steel circle stick, and keep fibriform, as the material with SUS304 and SUS316, pull it because a strain strength and a cutting stress is large, electrostatic removing effect and firm are using, though it is good at as being, electric resistance is extremely small bend as being entangled of Carl electrode can easily occur. Electrode fall electrode sharp, of are necessary to consider it not to be electric resistance is small, because a line diameter is small around a high-pressure circuit usefully.
    3. Sunderion Plastic fiber
      ·Line diameter=15µm(200denier/80filament)
      ·electric peculiar resistance=101ohms/cm
      With the substance to make a conductor mislead with a dyeing form for copper ion for acrylic fiber, because electric resistance is scantly, large for a line diameter, highly, badly and, though it is apt to be evaluated, electrode softly, moreover reconstruction also electrostatic removing effect is good especially, in case that it is useful with a contact form, in order to be good. It is most suitable for soft paper thin paper.
    4. Heat-resistant Dina fiber
      ·Line diameter=27µm(3200denier/36filament)
      ·electric peculiar resistance=10-3ohms/cm
      For others also, Carl, electrode sharp, fully pull it more than crbon fiber and have for a strength, as being a little there makes copper associative, enhance heat-resistance, by processing a special metal further, are a guidance electricity performance equal to a carbon fiber for polyvinylalcohol, and a fiber of a lineage.
    5. SA-7 fiber
      ·Line diameter=24µm
      ·electric peculiar resistance=105ohms/cm
      In order to be extremely expansive for peculiar low resisting, an electrostatic removing performance performance isn't good enough. However must small place and, an electric discharge amperage does and is useful for a place to take and exclude a trash for the state to pile up an electrode. Must small place and, an alectric discharge amperage does and is useful for a place to remove a trash for the state to pile up an electrode.
    6. Amolfas metel fiber
      ·Line diameter=20µm
      ·electric peculiar resistance=10-4ohms/cm
      As facing it, so that a general metal is crystal structure that Motoko are regular and arrange, Amolfas metal fiber is the metal that it misleads piece on the condition of high pressure.
      For the metal that I mislead piece on the condition of high pressure, the substance that does for a state of a fiber is Amolfas metal fiber.
      Pull it then, strain strength, a twin friction food performance, and a magnetic characteristic at for a non-crystal, a peculiar defect of a metal crystal is excluded a superb characteristic is shown.
      Have a possibility Amolfas metal fiber can make a material to have a new characteristic further.
    7. Electrostatic removing seat
      Try with no a metal of guidance electricity durability electrostatic removing seat is. Then, that does a shape of a non-cloth and is light-weight moreover.
      An amount gets cheap as being easy for structure.
      Guidance electricity a thickness of a non-cloth electrode is 68µm. An electric low resisting(I include a support body) is 50ohms following. A content metal is Nickelic. For a pull strain strength, more than 10kg/5cm, heat-resistance becomes 100°C following. Electrostatic remobing effect is the remaining voltage 50V following with an operation once, in the early time against a belt voltage DC1000V.(however, use a tape guidance electricity)